收藏本站
SETPOINT OUTPUT TIME-OUT
COUNTER AUTO RESET
SPn tOUt ?
? 001.00
0.01
to
599.99
seconds
SPn AUtO
?
?
NO
NO
@2Ero-Str
2Ero-End
CtLd-Str
CtLd-End
This parameter is only active if the Setpoint Action is set to time out ( t-OUt ).
Enter the value in seconds that the Setpoint output will be active, once the
Setpoint Value is reached.
SETPOINT VALUE
This parameter automatically resets the counter to which the setpoint is
assigned ( SPn ASN ) each time the setpoint value is reached. The automatic reset
can occur at output start, or at output end if the Setpoint Output Action is
programmed for timed output mode. The Reset-to-Count Load selections
(“ CtLd- ”) only apply to Counter A assignment. This reset may be different from
the Counter A Reset Action selected in Module 1.
SPn VAL ?
? 00000100
Count A:
Count B:
Rate:
- 9999999 to 99999999
0 to 9999999
0 to 999999
SELECTION ACTION
NO No Auto Reset.
2Ero-Str Reset to Zero at the start of output activation.
CtLd-End Reset to out only). Load value at the end of output activation
?
SP1 OFF2 ?
?
SP2 OFF1 ?
?
Enter  the  desired  Setpoint  value.  To  enter  a  negative  setpoint  value,
increment digit 8 to display a “-” sign (Counter A only).
SETPOINT OUTPUT LOGIC
SPn OUt ?
NOr rEV
NOr
Normal ( NOr ) turns the output “on” when activated and “off” when
deactivated. Reverse ( rEV ) turns the output “off” when activated and “on” when
deactivated.
SETPOINT ANNUNCIATOR
SPn LIt ? NOr                rEV
? NOr
Normal ( NOr ) displays the setpoint annunciator when the corresponding
output is “on”. Reverse ( rEV ) displays the setpoint annunciator when the output
is “off”.
SETPOINT OUTPUT POWER-UP STATE
CtLd-Str Reset to Count Load value at the start of output activation.
2Ero-End Reset to Zero at the end of output activation (timed out only).
Count
(timed
SETPOINT 1 OUTPUT OFF AT SETPOINT 2 (SP1 Only)
NO Out2-Str Out2-End
NO
This parameter will deactivate Setpoint 1 output at the Start or End of
Setpoint 2 output (O1 off at O2). The “ -End ” setting only applies if Setpoint 2
Output Action is programmed for timed output.
SETPOINT 2 OUTPUT OFF AT SETPOINT 1 (SP2 Only)
NO Out1-Str Out1-End
NO
This parameter will deactivate Setpoint 2 output at the Start or End of
Setpoint 1 output (O2 off at O1). The “ -End ” setting only applies if Setpoint 1
Output Action is programmed for timed output.
SPn P-UP
?
OFF
ON
SAVE
SETPOINT OUTPUT RESET WITH MANUAL RESET
?
?
SPn StbY ?
?
? OFF
SAVE will restore the output to the same state it was at before the meter was
powered down. ON will activate the output at power up. OFF will deactivate the
output at power up.
SETPOINT BOUNDARY TYPE
SPn tYPE ? HI-ACt          LO-ACt
? HI-ACt
High Acting Boundary Type activates the output when the assigned display
value ( SPn ASN ) equals or exceeds the Setpoint value. Low Acting activates the
output when the assigned display value is less than or equal to the Setpoint.
SETPOINT STANDBY OPERATION
NO YES
NO
This parameter only applies to Low Acting Boundary Type setpoints. Select
YES to disable a Low Acting Setpoint at power-up, until the assigned display
value crosses into the output “off” area. Once in the output “off” area, the
Setpoint will then function per the description for Low Acting Boundary Type.
12
SPn rSt ?
YES NO
YES
Selecting YES causes the Setpoint output to deactivate (reset) when the
Setpoint Assigned Counter is reset. The counter reset can occur by the RST
button, User Input, Counter Reset at Power-up or a serial Reset Counter
command.
This output reset will not occur when the Assigned Counter is reset by a
Setpoint generated Counter Auto Reset.
CHANGE DISPLAY COLOR WITH OUTPUT STATE
SPn ChC ?
NO YES
NO
This parameter enables the backlight CUB5 to switch the backlight color when
the output state changes. This parameter is only active for the backlight version.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
P51-750-A-I-P-5V-000-000 SENSOR 750PSI 7/16-20 UNF 1-5V
ASFLMPC-48.000MHZ-Z-T OSC 48.000 MHZ CMOS MEMS SMD
P51-500-A-I-P-5V-000-000 SENSOR 500PSI 7/16-20 UNF 1-5V
P51-300-A-I-P-5V-000-000 SENSOR 300PSI 7/16-20 UNF 1-5V
P51-200-A-I-P-5V-000-000 SENSOR 200PSI 7/16-20 UNF 1-5V
SCUB1000 COUNTER DISPLAY SCUB1000 + DATA
P51-100-A-I-P-5V-000-000 SENSOR 100PSI 7/16-20 UNF 1-5V
P51-75-A-I-P-5V-000-000 SENSOR 75PSI 7/16-20 UNF 1-5V
相关代理商/技术参数
CUB5RLY0 功能描述:BOARD RELAY PLUG-IN FOR CUB5 RoHS:是 类别:工业控制，仪表 >> 配件 系列:* 标准包装:1 系列:Aero-Motive® 130117 附件类型:拖车带 适用于相关产品:标准盒式跟踪系统 其它名称:WM6183
CUB5RTB0 制造商:Red Lion Controls 功能描述:PANEL METER; RTD METER WITH RED/GREEN BACKLIGHT DISPLAY 制造商:Red Lion Controls 功能描述:RTD METER WITH RED/GREEN 制造商:Red Lion Controls 功能描述:TEMPERATURE DISPLAY FOR RTD 制造商:Red Lion Controls 功能描述:PANEL DISPLAY, TEMPERATURE, 95mA, 9V TO 28V; No. of Digits / Alpha:5; Meter Function:Temperature; Meter Range:-19999 to +19999; Digit Height:12.2mm; Panel Cutout Height:39.1mm; Panel Cutout Width:74.9mm
CUB5RTR0 功能描述:RTD METER REFLECTIVE RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030
CUB5SNK0 功能描述:DUAL SINKING OPEN OC OUT CARD RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030
CUB5TB00 功能描述:TIMER & CYCLE COUNTER W/BKLT RoHS:是 类别:工业控制，仪表 >> 计数器 系列:* 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮
CUB5TCB0 功能描述:METER PANEL LCD THERMOCOUPLE RED RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:CUB5 标准包装:12 系列:* 其它名称:Q7072030
CUB5TCR0 功能描述:THERMO METER REFLECTIVE RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030
CUB5TR00 制造商:Red Lion Controls 功能描述:PRESET TIMR & CYCLE COUNTR W/REFL DSPLY 制造商:Red Lion Controls 功能描述:TIMER, ELECTRONIC , 8DIGIT, 9V TO 28V; Supply Voltage Range:9V DC to 28V DC; Panel Cutout Height:39.1mm; Panel Cutout Width:74.9mm; Time Range:- ;RoHS Compliant: Yes